View EDEV-BF5XX_8418674.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

hardware user manual edev - bf5xx v2.0
edev - bf5xx_hum_v2.0.docx 2 contact bluetechnix mechatronische systeme gmbh waidhausenstr a?e 3/19 a - 1140 vienna austria/europe office@bluetechnix.at http://www.bluetechnix.com document no.: 100- 2342- 2 - 2 . 6 date: 2012- 03- 26
edev - bf5xx_hum_v2.0.docx 3 table of contents blackfin ? core modu les ............................................................................................................................................................................ 6 blackfin ? development boards ............................................................................................................................................................. 8 1 introduction ....................................................................................................................................................................................... 9 1.1 overview .................................................................................................................................................................................... 9 1.2 key features ........................................................................................................................................................................... 10 1.3 applications ............................................................................................................................................................................ 11 2 general description ...................................................................................................................................................................... 12 2.1 functional description ....................................................................................................................................................... 12 2.1.1 powering ........................................................................................................................................................................ 13 2.1.2 data line buffering .................................................................................................................................................... 13 2.1.3 usb ................................................................................................................................................................................... 13 2.1.4 ethernet .......................................................................................................................................................................... 13 2.1.5 sd - card ........................................................................................................................................................................... 13 2.1.6 image sensors (blt - ism - connector) .................................................................................................................. 13 2.1.7 rgb - tft display .......................................................................................................................................................... 13 2.2 pcb placement ...................................................................................................................................................................... 14 2.3 mechanical outline .............................................................................................................................................................. 15 2.4 extender board footprint ................................................................................................................................................. 17 3 specifications ................................................................................................................................................................................... 18 3.1.1 operating conditions ............................................................................................................................................... 18 3.1.2 maximum ratings ....................................................................................................................................................... 18 3.1.3 esd sensitivity ............................................................................................................................................................. 18 4 connector description ................................................................................................................................................................. 19 4.1 extension connector x1 .................................................................................................................................................... 19 4.2 extension connector x2 .................................................................................................................................................... 22 4.3 image sensor connector x11 (blt - ism - connector) ............................................................................................... 26 4.4 display connector x6 ......................................................................................................................................................... 26 5 switches, jumpers and leds ..................................................................................................................................................... 28 5.1 power led ............................................................................................................................................................................... 28 5.2 gpio leds ................................................................................................................................................................................ 28 5.3 gpio button ............................................................................................................................................................................ 28 5.4 reset button ........................................................................................................................................................................... 28 5.5 board configuration switches ( s2, s3) ......................................................................................................................... 28 5.6 boot mode switch (s6) ....................................................................................................................................................... 29 5.7 uart routing switch (s5) ................................................................................................................................................. 30 6 support .............................................................................................................................................................................................. 31
edev - bf5xx_hum_v2.0.docx 4 6.1 general support .................................................................................................................................................................... 31 6.2 board support packages ................................................................................................................................................... 31 6.3 blackfin? software support .............................................................................................................................................. 31 6.3.1 blacksheep? os ........................................................................................................................................................ 31 6.3.2 labview ......................................................................................................................................................................... 31 6.3.3 uclinux ............................................................................................................................................................................ 31 6.4 blackfin ? design services ................................................................................................................................................... 31 6.4.1 upcoming products and software releases .................................................................................................... 31 7 ordering information ................................................................................................................................................................... 32 7.1 predefined mount ing options for edev - bf5xx ........................................................................................................ 32 8 dependability .................................................................................................................................................................................. 33 8.1 mtbf .......................................................................................................................................................................................... 33 9 product history ............................................................................................................................................................................... 34 9.1 version information ............................................................................................................................................................. 34 9.2 anomalies ................................................................................................................................................................................ 34 10 document revision history ................................................................................................................................................... 35 11 list of abbreviations ................................................................................................................................................................ 36 a list of figures and tables ............................................................................................................................................................ 37
edev - bf5xx_hum_v2.0.docx 5 ? bluetechnix mechatronische systeme gmbh 201 2 all rights reserved. the information herein is given to describe certain components and shall not be considered as a guarantee of characteristics. terms of delivery and rights of technical change reserved. we hereby disclaim any warranties, including but not limited to warranties of non - infringement, regarding circuits, descriptions and charts stated herein. bluetechnix makes and you receive no warranties or conditions, express, implied, statutory or in any co mmunication with you. bluetechnix specifically disclaims any implied warranty of merchantability or fitness for a particular purpose. bluetechnix takes no liability for any damages and errors causing of the usage of this board. the user of this board is re sponsible by himself for the functionality of his application. he is allowed to use the board only if he has the qualification. more information is found in the general terms and conditions (agb). information for further information on technology, delivery terms and conditions and prices please contact bluetechnix (http://www.bluetechnix.com). warning due to technical requirements components may contain dangerous substances.
edev - bf5xx_hum_v2.0.docx 6 b lackfin ? core modules tcm - bf518 - c - c - q25s32f2 (tcm - bf518) the tiny core module t cm - bf518 is powered by analog devices' single core adsp - bf518 processor; up to 400mhz, 32mb sdram, up to 8mb flash. the 2x60 pin expansion connectors are backwards compatible with other core modules. acm - bf525c - c - c - q25s64f4n1024 the core module acm - bf525c is optimized for audio applications and performance. it is based on the high performance adspbf525cfrom analog devices. it addresses 64mbyte sdram via its 16bit wide sdram bus, has an onboard nor - flash of 4mbyte and a nand - flash with 1024mbyte. cm - bf527 - c - c - q50s32f8 (cm - bf527) the core module cm - bf527 is powered by analog devices' single core adsp - bf527 processor; key features are usb otg 2.0 and ethernet. the 2x60 pin expans ion connectors are backwards compatible with other core modules. cm - bf533 - c - c - q25s32f2 (cm - bf533) the core module cm - bf533 is powered by analog devices' single core adsp - bf533 processor; up to 600mhz, 32mb sdram, 2mb flash, 2x60 pin expansion connectors a t a size of 36.5x31.5mm. tcm - bf537 - c - i - q25s32f8 (tcm - bf537) the tiny core module tcm - bf537 is powered by analog devices' single core adsp - bf537 processor; up to 500mhz, 32mb sdram, 8mb flash, a size of 28x28mm, 2x60 pin expansion connectors, ball grid array or border pads for reflow soldering, industrial temperature range - 40c to +85c. cm - bf537 - c - c - q25s32f4 (cm - bf537e) the core module cm - bf537 is powered by analog devices' single core adsp - bf537 processor; up to 600mhz, 32mb sdram, 4mb flash, integrated tp10/100 ethernet physical transceiver, 2x60 pin expansi on connectors a t a size of 36.5x31.5mm. cm - bf537 - c - c - q30s32f4 - u (cm - bf537u) the core module cm - bf537 is powered by analog devices' single core adsp - bf537 processor; up to 600mhz, 32mb sdram, 4mb flash, integrated usb 2.0 device, 2x60 pin expansion connectors at a size of 36.5x31.5mm. cm - bf548 - c - c - q25s64f8 (cm - bf548) the core module cm - bf548 is characterized by its numerous peripheral interfaces, its performance in combination with its high speed memory interface (ddr) . k ey features are 533 mhz , 64mb ddr sd - ram (266mhz), and 8mb flash. cm - bf561 - c - c - q25s64f8 (cm - bf561) the core module cm - bf561 is powered by analog devices' dual core adsp - bf561 processor; up to 2x 600mhz, 64mb sdram, 8mb flash , 2x60 pin expansion connectors at a size of 36.5x31.5mm. ecm - bf561 - c - c - q25s128f32 (ecm - bf561) the core module cm - bf561 is powered by analog devices' dual core adsp - bf561 processor; up to 2x 600mhz, 128 mb sdram, 8mb flash, 2x 100 pin expansion connectors and a size of 44 x3 3 mm.
edev - bf5xx_hum_v2.0.docx 7 core module naming information the idea is to put more core module specific technical information into the product name. new core module names w ill have following technical information covered in their names. ? product family, ? cpu - type, ? connection - type, ? operating temperature range, ? crystal frequency [mhz], ? ram [mb], ? flash [mb], ? external controllers ? o special and/or o ptional o former name that expands of course the name but allows the customer to get the most important core module specific information at the first sight. have a look at the example below to get an idea of the new core module names. example cm - bf537 - c - c - q25s32f4 (cm - bf537e) - - - - - - product family former name cm = core modul e special sbc = single board computer custom core modules or specials cpu-type uc = uclinux equals the name of cpu extra controllers mounted connection-type e = ethernet a = bga u = usb b = border pad flash [mb] c = connector f = nor flash [mb] s = s speci al n = nand fl as h [mb] operating temperature range ram a = automoti ve (-40 to +125) s = sdram [mb] c = commerci al (0 to +70) i = industry (-40 to +85) crystal frequency notati on: qxx[mhz] f4 (cm-bf537e) s32 cm bf537 c c q25
edev - bf5xx_hum_v2.0.docx 8 b lackfin ? development boards adev - bf52xc f eature rich, low cost embedded audio development platform which supports audio core modules (acm). the form factor of the adev - bf5 2 x c allows easy integration of the board into oem products. dedicated interfaces such as usb2.0, line in/out, headphone out and an onboard silicon microphone turn the adev - bf52xc into a full - featured development platform for most embedded audio applications i n commercial areas. dev - bf5xxda - lite get ready to program and debug bluetechnix core modules with this tiny development platform including an usb - based debug agent. the dev - bf5xxda - lite is a lo w cost starter development system including a vdsp++ evaluation software license. dev - bf548 - lite low - cost development board with a socket for bluetechnix cm - bf548 core module. additional interfaces are available, e.g. an sd - card, usb and ethernet. dev - bf548da - l ite get ready to program and debug bluetechnix cm - bf548 core module with this tiny de velopment platform including an usb - based debug agent. the dev - bf548da - lite is a low - cost starter development system including a vdsp++ evaluation software license. edev - bf5xx f eature rich, low cost rapid development platform which provides all interfaces on dedicated connectors and has all core module pins routed to solder pads which easily can be accessed by the developers. the edev - bf5xx supports the latest debugging interface from analog devices - adi - sada (analog devices stand alone debug agent) . eval - bf5xx tiny, low cost embedded platform which supports bluetechnix powerful blackfin? based core modules. the form factor (75x75mm) of the eval - bf5xx allows easy integration of the board into oem products. dedicated interfaces such as usb2.0, sd - card slot, can interface connectors and of course ethernet, turn the eval - bf5xx into a full - featured evaluation platform for most e mbedded applications. extender b oards e xtender b oards (ext - bf5xx) are expanding the development and evaluation boards by several interfaces and functionalities. targeted application areas are: audio/video processing, security and surveillance, ethernet access, positioning, automation and control, experimental development and measuring. note! bluetechnix is offering tailored board developments as well.
edev - bf5xx_hum_v2.0.docx 9 1 introduction the edev - bf5xx development board is a feature rich, low cost rapid development platform designed to decrease time - to - market of customized applications. it supports bluetechnix powerful blackfin? based core modules like the latest ecm - bf561. the development board provides all interfaces on dedicated connectors and has all core module pins routed to solder pads which can be easily accessed by the developers. this allows customers to connect their own hardware and enables comfortable measurements. interfaces such as a high - speed serial port which is directly connectable to a computer usb port, an usb 2.0 device controller, a lan controller and an sd - card socket are available. the edev - bf5xx supports the latest d ebugging interface from analog devices - adi - sada ( analog devices stand alone debug agent ) which is fully compatible with visual dsp++ and allows programming and debugging any of the blackfin? p rocessors. of course the d evelopment b oard is compatible with your adi high performance debug agent. the edev - bf5xx features the latest extender socket (bottom side) for upcoming extender boards. 1.1 overview figure 1 - 1 shows the main parts of the development board. 187 solderpads usb to uart ecm-bf561 120 pin expansion connector a debug agent usb 2.0 device controller lan controller dc/dc power supply (5v and 3v3) sd-card cam interface tft interface touchscreen controller 120 pin expansion connector b figure 1 - 1 : main c omponents of edev - bf5xx
edev - bf5xx_hum_v2.0.docx 10 1.2 key features ? ecm - bf561 core module slot o mating with ecmbf561 core module o two mounting holes allow fixing the core module with two m2 screws ? usb to uart converter o silabs cp2102 usb to uart bridge o mini usb - b connector ? usb 2.0 device controller o plx technology net2272 usb device controller o mini usb - b connector ? ethernet controller o smsc lan9218 ethernet cont roller o rj45 connector with 2 leds o 93c46b/sn eeprom for mac storage ? power supplies o dc - plug o 3.3v switching supply for all devices except sada (max. 2a) o 5.0v switching supply for sada (max. 0.5a) o programmable ldo1 (default 1.8v) core voltage supply for image sensor (max. 300ma) o programmable ldo2 (default 2.85v) analog and io voltage for image sensor (max. 300ma) ? touch s creen controller o texas instruments tsc2003 o i2c interface ? tft connector o 40 pin zif connector o various edt displays available (3,5 to 7; 320x240 to 800x480) ? camera connector (blt - ism - connector) o 30 pin zif connector o compatible with all bluetechnix image sensor modules ? sd - card slot o compatible with sd hc - cards o spi interface ? 2x 120 pin extension co nnector o 2x samtec qsh - 060- 01- l - d - a o all ecm pins and additional power pins available ? 187 solder pads o all ecm pins and available o 2.45mm (0.1) pitch spacing to solder standard headers or sockets for testing own hardware ? leds o 1 power led o leds (red and green) on gpios ? button o reset button o 1 button on gpio
edev - bf5xx_hum_v2.0.docx 11 1.3 applications ? parallel digital signal processing ? imaging and consumer multimedia ? set top boxes ? automotive vision systems ? portable media players ? digital video camera systems ? video conference applications ? image recognition ? video streaming application
edev - bf5xx_hum_v2.0.docx 12 2 general description the edev - bf5xx is a powerful evaluation platform designed for the latest blackfin based core modules of bluetechnix . it features a connector slot for a core module and offers wide spread connecti vity possibilities. the usb and ethernet c ontrollers are connected to the blackfin s ebi (external bus interface). an interface for the bluetechnix image sensor modules (ism) as well as a tft connector is on board. the image sensors are routed to ppi0. th e tft connector operates with tft d isplays from edt with the standard family - concept interface . it is routed to the ppi1 of the core module. an additional touch screen controller is connected to gpios. a jtag connector is available to connect your high spe ed jtag from analog devices or the adi - sada ( analog devices stand alone debug agent ). the sd - card socket is routed to the spi port of the core module. the edev - bf5xx has all core module pins routed to solder pads in order to ensure a good connectivity of external hardware. 2.1 functional descriptio n dc-socket solder pads uart to usb ecm-bf561 120 pin expansion connector a debug agent usb 2.0 device controller lan controller dc/dc power supply (5v and 3v3) sd-card cam interface tft interface touch screen controller 120 pin expansion connector b solder pads mini-usb-b jtag mini- usb-b ebi jtag uart gpio ppi1 ppi0 mini-usb-b rj45 spi figure 2 - 1 : interconnection d iagram
edev - bf5xx_hum_v2.0.docx 13 2.1.1 powering the edev - bf5xx must be powered externally by connecting a dc source to the dc - plug. the voltage can vary between 7v and 24v. the on - board regulators are generating the 5.0v supply for the sada and the 3.3v supply for the core module and all other devices. 2.1.2 data line buffering to guarantee that devices externally connected to the ebi are working without any problems, line buffers are connected to the 32 - bit data bus. for buffering the 74lvt16245mtd with 3 - state outputs is used. 2.1.3 usb there are two usb connectors on the development board. one is connected to an uart to usb converter (x8), the second to the usb 2.0 device controller (x7). the cp2102 usb to uart bridge from silicon labs is connected to the uart0 of the blackfin. this usb connection is easy to use and ideal for debug outputs on the pc. the needed drivers are available on the manu facturers website: http://www.silabs.com/products/mcu/pages/usbtouartbridgevcpdrivers.aspx . the uart is also available on a standard 4 - pin 2.54mm pitch header. to change the uart routing the right switcher setting (s5) has to be made. the net2272 usb device controller from plx technology is connected to the ebi. if the controller wont be used, he can be disabled by setting the right configuration on the dip - switches (see chapter 5.5 ). the net2272 is usb v2.0 compliant and provides a high speed usb connection to a usb host. 2.1.4 ethernet the lan9218 is a 10/100 base - t ethernet controll er from smsc with integrated mac and phy. the controller is fully ieee 802.3/802.3u compliant; the phy supports hp - auto - mdix. 2.1.5 sd - card the sd - card slot is located on the bottom side of the board. the cards are connected via spi to the blackfin, a 4 - bit para llel data transmission mode is not supported. 2.1.6 image sensor s (blt - ism - connector) the 30 - pin zif socket allows connecting image sensor modules (ism) from bluetechnix. the ism is connected to the ppi0 of the core module. there are a various number of isms ava ilable. please check out our website for an actual l ist of available m odules. 2.1.7 rgb - tft display another zif socket (40 - pin) is allows connecting a tft - display to the ppi1 of the core module. the connector is compatible with different tft displays from edt (emerging display technologies). contact bluetechnix for a list of currently supported d isplays.
edev - bf5xx_hum_v2.0.docx 14 there is also a touch screen controller on board (tcs2003) accessible via i2c. 2.2 pcb placement figure 2 - 2 shows the position of the connectors, switches and leds on the board. figure 2 - 2 : interface overview
edev - bf5xx_hum_v2.0.docx 15 2.3 mec hanical outline figure 2 - 3 : mechanical o utline t op view
edev - bf5xx_hum_v2.0.docx 16 figure 2 - 4 : mechanical o utline b ottom view
edev - bf5xx_hum_v2.0.docx 17 2.4 extender board footprint figure 2 - 5 shows the recommended extension board layout used also for bluetechnix extension boards. for the detailed dimensions for the extension board connectors (qth - 060- 01- l - d - a from samtec) pl ease refer the samtec product manual. figure 2 - 5 : recommended e xtender b oard l ayout
edev - bf5xx_hum_v2.0.docx 18 3 specification s 3.1.1 operating conditions symbol parameter min typical max unit v in input supply voltage 7 24 v i 3v3 3.3v current tbd a i 5v0 1) 5.0v current tbd a v rtc 2) real - time clock supply voltage tbd tbd v i rtc 2) v rtc current tbd a table 3 - 1 : electrical c haracteristics 1) only in adi - sada is used, otherwise the 5.5v is unloaded. 2) the ecm - bf561 has no rtc. this power supply is reserved for future use. 3.1.2 maximum ratings stressing the device above the rating listed in the absolute maximum ratings table may cause permanent damage to the device. these are stress ratings only. operation of the device at these or any other conditions greater than those indicated in the operating sections of this specification is not implied. exposure to absolute maximum rating conditions for ex tended periods may affect device reliability. symbol parameter min max unit v io input or output voltage - 0.5 3.6 v v in input supply voltage - 0.5 24 v t amb ambient temperature - 0 85 c t sto storage temperature - 55 150 c t sld solder temperature for 10 seconds 260 c amb relative ambient humidity 90 % table 3 - 2 : absolute m aximum r atings 3.1.3 esd sensitivity esd (electrostatic discharge) sensitive device. charged devices and circuit boards can discharge without detection. although this product features patented or proprietary protection circuitry, damage may occur on devices subjected to high energy esd. therefore, proper esd precautions should be taken to avoid performance degradation or loss of function ality.
edev - bf5xx_hum_v2.0.docx 19 4 connector description 4.1 extension connector x1 pin name type alt ernative function description 1 gnd pwr power ground 2 gnd pwr power ground 3 ppi0.d8 i/o pf40 parallel peripheral interface 0 data 4 ppi0.d0 i/o parallel peripheral interface 0 data 5 ppi0.d9 i/o pf41 parallel peripheral interface 0 data 6 ppi0.d1 i/o parallel peripheral interface 0 data 7 ppi0.d10 i/o pf42 parallel peripheral interface 0 data 8 ppi0.d2 i/o parallel peripheral interface 0 data 9 ppi0.d11 i/o pf43 parallel peripheral interface 0 data 10 ppi0.d3 i/o parallel peripheral interface 0 data 11 ppi0.d12 i/o pf44 parallel peripheral interface 0 data 12 ppi0.d4 i/o parallel peripheral interface 0 data 13 ppi0.d13 i/o pf45 parallel peripheral interface 0 data 14 ppi0.d5 i/o parallel peripheral interface 0 data 15 ppi0.d14 i/o pf46 parallel peripheral interface 0 data 16 ppi0.d6 i/o parallel peripheral interface 0 data 17 ppi0.d15 i/o pf47 parallel peripheral interface 0 data 18 ppi0.d7 i/o parallel peripheral interface 0 data 19 ppi0.sy3 i/o parallel peripheral interface 0 sync 3 20 ppi0.sy2 i/o tmr9 parallel peripheral interface 0 sync 2 21 gnd pwr power ground 22 ppi0.sy1 i/o tmr8 parallel peripheral interface 0 sync 1 23 ppixd16 - rfu 24 ppi0.clk i clock input for parallel peripheral interface 0 25 ppixd17 - rfu 26 gnd pwr power ground 27 ppixd18 - rfu 28 ppi1.d0 i/o parallel peripheral interface 1 data 29 ppixd19 - rfu 30 ppi1.d1 i/o parallel peripheral interface 1 data 31 ppixd20 - rfu 32 ppi1.d2 i/o parallel peripheral interface 1 data 33 ppixd21 - rfu 34 ppi1.d3 i/o parallel peripheral interface 1 data 35 ppixd22 - rfu 36 ppi1.d4 i/o parallel peripheral interface 1 data 37 ppixd23 - rfu 38 ppi1.d5 i/o parallel peripheral interface 1 data
edev - bf5xx_hum_v2.0.docx 20 pin name type alt ernative function description 39 gnd pwr power ground 40 ppi1.d6 i/o parallel peripheral interface 1 data 41 can_tx - rfu 42 ppi1.d7 i/o parallel peripheral interface 1 data 43 can_rx - rfu 44 ppi1.d8 i/o pf32 parallel peripheral interface 1 data 45 pf9 i/o gpio 46 ppi1.d9 i/o pf33 parallel peripheral interface 1 data 47 pf8 i/o gpio 48 ppi1.d10 i/o pf34 parallel peripheral interface 1 data 49 gnd pwr power ground 50 ppi1.d11 i/o pf35 parallel peripheral interface 1 data 51 sp1.rsclk i/o pf30 serial port 1 receive clock 52 ppi1.d12 i/o pf36 parallel peripheral interface 1 data 53 sp1.rfs i/o pf24 serial port 1 receive frame sync 54 ppi1.d13 i/o pf37 parallel peripheral interface 1 data 55 sp1.drpri i serial port 1 primary data receive 56 ppi1.d14 i/o pf38 parallel peripheral interface 1 data 57 sp1.drsec i pf25 serial port 1 secondary data receive 58 ppi1.d15 i/o pf39 parallel peripheral interface 1 data 59 gnd pwr power ground 60 gnd pwr power ground 61 gnd pwr power ground 62 gnd pwr power ground 63 sp1.tsclk i/o pf31 serial port 1 transmit clock 64 ppi1.sy3 i/o parallel peripheral interface 1 sync 3 65 sp1.tfs i/o pf21 serial port 1 transmit frame sync 66 ppi1.sy2 i/o tmr11 parallel peripheral interface 1 sync 2 67 sp1.dtpri o pf23 serial port 1 primary data transmit 68 ppi1.sy1 i/o tmr10 parallel peripheral interface 1 sync 1 69 sp1.dtsec o pf22 serial port 1 secondary data transmit 70 ppi1.clk i clock input for parallel peripheral interface 1 71 spi.mosi o serial peripheral interface data output 72 3v3 pwr 3.3v power supply 73 spi.miso i serial peripheral interface data input 74 3v3 pwr 3.3v power supply 75 spi.sck o serial peripheral interface clock 76 3v3 pwr 3.3v power supply 77 gnd pwr power ground 78 gnd pwr power ground 79 clkbuf o buffered blackfin master clock output 80 gnd pwr power ground 81 gnd pwr power ground
edev - bf5xx_hum_v2.0.docx 21 pin name type alt ernative function description 82 gnd pwr power ground 83 sp0.rsclk i/o pf28 serial port 0 receive clock 84 nnmi0 i non maskable interrupt for core 0 85 sp0.rfs i/o pf19 serial port 0 receive frame sync 86 nnmi1 i non maskable interrupt for core 1 87 sp0.drpri i serial port 0 primary data receive 88 uart.rx i/o pf27 uart1 receive data 89 sp0.drsec i pf20 serial port 0 secondary data receive 90 uart.tx i/o pf26 uart1 transmit data 91 sp0.tsclk i/o pf29 serial port 0 transmit clock 92 gnd pwr power ground 93 sp0.tfs i/o pf16 serial port 0 transmit frame sync 94 nc - not connected 95 sp0.dtpri o pf18 serial port 0 primary data transmit 96 uart2.rx - rfu 97 sp0.dtsec o pf17 serial port 0 secondary data transmit 98 uart2.tx - rfu 99 pf14 i/o gpio 100 nc - not connected 101 pf13 i/o gpio 102 nc - not connected 103 pf12 i/o gpio 104 gnd pwr power ground 105 pf11 i/o gpio 106 gnd pwr power ground 107 pf10 i/o gpio 108 gnd pwr power ground 109 gnd pwr power ground 110 nc - not connected 111 gnd pwr power ground 112 nc - not connected 113 gnd pwr power ground 114 nc - not connected 115 3v3 pwr 3.3v power supply 116 vin pwr input voltage from dc connector 117 3v3 pwr 3.3v power supply 118 vin pwr input voltage from dc connector 119 3v3 pwr 3.3v power supply 120 vin pwr input voltage from dc connector s1 gnd shield shield ground s2 gnd shield shield ground s3 gnd shield shield ground s4 gnd shield shield ground
edev - bf5xx_hum_v2.0.docx 22 pin name type alt ernative function description s5 gnd shield shield ground s6 gnd shield shield ground s7 gnd shield shield ground s8 gnd shield shield ground table 4 - 1 - connector description x1 4.2 extension connector x2 pin name type alt ernative function description 1 gnd pwr power ground 2 gnd pwr power ground 3 ebi.nabe0 o byte enable 0 (active low) 4 a12 o address bus 5 ebi.nabe1 o byte enable 1 (active low) 6 a13 o address bus 7 ebi.nabe2 o byte enable 2 (active low) 8 a14 o address bus 9 ebi.nabe3 o byte enable 3 (active low) 10 a15 o address bus 11 a2 o address bus 12 a16 o address bus 13 a3 o address bus 14 a17 o address bus 15 a4 o address bus 16 a18 o address bus 17 a5 o address bus 18 a19 o address bus 19 a6 o address bus 20 a20 o address bus 21 a7 o address bus 22 a21 o address bus 23 a8 o address bus 24 a22 o address bus 25 a9 o address bus 26 a23 o address bus 27 a10 o address bus 28 a24 o address bus 29 a11 o address bus 30 a25 o address bus 31 gnd pwr power ground 32 gnd pwr power ground 33 gnd pwr power ground
edev - bf5xx_hum_v2.0.docx 23 pin name type alt ernative function description 34 gnd pwr power ground 35 gnd pwr power ground 36 gnd pwr power ground 37 3v3 pwr 3.3v power supply 38 3v3 pwr 3.3v power supply 39 3v3 pwr 3.3v power supply 40 3v3 pwr 3.3v power supply 41 3v3 pwr 3.3v power supply 42 3v3 pwr 3.3v power supply 43 d0 i/o data bus 44 d16 i/o data bus 45 d1 i/o data bus 46 d17 i/o data bus 47 d2 i/o data bus 48 d18 i/o data bus 49 d3 i/o data bus 50 d19 i/o data bus 51 d4 i/o data bus 52 d20 i/o data bus 53 d5 i/o data bus 54 d21 i/o data bus 55 d6 i/o data bus 56 d22 i/o data bus 57 d7 i/o data bus 58 d23 i/o data bus 59 gnd pwr power ground 60 gnd pwr power ground 61 gnd pwr power ground 62 gnd pwr power ground 63 d8 i/o data bus 64 d24 i/o data bus 65 d9 i/o data bus 66 d25 i/o data bus 67 d10 i/o data bus 68 d26 i/o data bus 69 d11 i/o data bus 70 d27 i/o data bus 71 d12 i/o data bus 72 d28 i/o data bus 73 d13 i/o data bus 74 d29 i/o data bus 75 d14 i/o data bus 76 d30 i/o data bus
edev - bf5xx_hum_v2.0.docx 24 pin name type alt ernative function description 77 d15 i/o data bus 78 d31 i/o data bus 79 nc - not connected 80 pf7 i/o spisel7 / tmr7 gpio 81 nreset i/o power on reset and reset input 82 pf6 i/o spisel6 / tmr6 gpio 83 nc - not connected 84 pf5 i/o spisel5 / tmr5 gpio 85 ebi.nams1 o asynchronous memory select 1 (active low) 86 pf4 i/o spisel4 / tmr4 gpio 87 ebi.nams2 o asynchronous memory select 2 (active low) 88 pf3 i/o spisel3 / tmr3 gpio 89 ebi.nams3 o asynchronous memory select 3 (active low) 90 pf2 i/o spisel2 / tmr2 gpio 91 ebi.naoe o asynchronous memory output enable (active low) 92 pf1 i/o spisel1 / tmr1 gpio 93 ebi.nare o asynchronous memory read enable (active low) 94 pf0 i/o spiss / tmr0 gpio 95 ebi.nawe o asynchronous memory write enable (active low) 96 pf15 i/o extclk gpio 97 ardy i address ready 98 gnd pwr power ground 99 gnd pwr power ground 100 nbg i/o bus grant (active low) 101 ebi.sclk o synchronous memory clock 102 nbr i bus request (active low) 103 gnd pwr power ground 104 nbgh i/o bus grant hang (active low) 105 gnd pwr power ground 106 rfu0 - rfu 107 gnd pwr power ground 108 otp - rfu 109 nc - not connected 110 gnd pwr power ground 111 nc - not connected 112 gnd pwr power ground 113 nc - not connected 114 gnd pwr power ground 115 vin pwr input voltage from dc connector 116 3v3 pwr 3.3v power supply 117 vin pwr input voltage from dc connector 118 3v3 pwr 3.3v power supply 119 vin pwr input voltage from dc connector
edev - bf5xx_hum_v2.0.docx 25 pin name type alt ernative function description 120 3v3 pwr 3.3v power supply s1 gnd shield shield ground s2 gnd shield shield ground s3 gnd shield shield ground s4 gnd shield shield ground s5 gnd shield shield ground s6 gnd shield shield ground s7 gnd shield shield ground s8 gnd pwr shield ground table 4 - 2 - connector d escription x2
edev - bf5xx_hum_v2.0.docx 26 4.3 image sensor connector x 11 (blt - ism - c onnector ) pin name type description 1 vdd pwr power supply 2 gnd pwr power ground 3 saddr i configuration bus address 4 extclk i mount option instead of onboard oscillator 5 nreset i reset (active low) 6 scl o configuration bus clock line 7 sda i/o configuration bus data line 8 rfu 9 gnd pwr power ground 10 pixclk o pixel clock 11 fv o frame valid (vsync) 12 lv o line valid (hsync) 13 trigger i camera trigger 14 strobe o strobe signal 15 d0 o pixel data0 16 d1 o pixel data1 17 d2 o pixel data2 18 d3 o pixel data3 19 vddio pwr i/o supply voltage 20 gnd pwr power ground 21 d4 o pixel data4 22 d5 o pixel data5 23 d6 o pixel data6 24 d7 o pixel data7 25 gnd pwr power ground 26 d8 o pixel data8 27 d9 o pixel data9 28 d10 o pixel data10 29 d11 o pixel data11 30 noe i output enable (active low) table 4 - 3 : blt - ism - connector i nterface d escription (x 11) 4.4 display connector x6 pin name type description 1 pf14 o display reset (shorted with pin 29) 2 gnd pwr power ground 3 ppi1.d15 o red data (msb) 4 ppi1.d14 o red data 5 ppi1.d13 o red data 6 ppi1.d12 o red data
edev - bf5xx_hum_v2.0.docx 27 pin name type description 7 ppi1.d11 o red data 8 ppi1.d15 o red data (lsb) 9 gnd pwr power ground 10 ppi1.d10 o green data (msb) 11 ppi1.d9 o green data 12 ppi1.d8 o green data 13 ppi1.d7 o green data 14 ppi1.d6 o green data 15 ppi1.d5 o green data (lsb) 16 gnd pwr power ground 17 ppi1.d4 o blue data (msb) 18 ppi1.d3 o blue data 19 ppi1.d2 o blue data 20 ppi1.d1 o blue data 21 ppi1.d0 o blue data 22 ppi1.d4 o blue data (lsb) 23 gnd pwr power ground 24 ppi1.clk o display data clock 25 gnd pwr power ground 26 ppi1.sy1 o hsync 27 ppi1.sy2 o vsync 28 ppi1.sy3 o data enable 29 pf14 o power control (shorted with pin 1) 30 3v3 pwr 3.3v power supply 31 gnd pwr power ground 32 gnd pwr power ground 33 3v3 pwr 3.3v power supply 34 3v3 pwr 3.3v power supply 35 nc - not connected 36 pf5/tmr5 o pwm for backlight dimming 37 tp_y+ ai analog t ouch screen input 38 tp_x - ai analog t ouch screen input 39 tp_y - ai analog t ouch screen input 40 tp_x+ ai analog t ouch screen input table 4 - 4 : display i nterface d escription (x6)
edev - bf5xx_hum_v2.0.docx 28 5 switches, jumpers and leds 5.1 power led the power led right next to the dc - plug indicates whether the core module is powered or not. the led goes on, if the 3.3v power supply is generates. 5.2 gpio leds each of the two leds (red and green) is connected via a dip switch (se e below) to a gpio of the core module. led color blackfin gpio v9 red pf6 v10 green pf7 table 5 - 1 : led c onnection d escription 5.3 gpio button one push - button is connected to the gpio pf10 . also this button (and the pull - up resistor) can be disconnected from the module. a hardware de - bouncing is realized by a single rc - element with a time - constant of =1ms. 5.4 reset button the reset button is connected to the core modules reset and to the camera reset on x11. he is also available on the extension connector x2. the hardware de - bounced signal ( =5.4ms) is gated with an open collector schmitt - trigger. 5.5 board configuration switches (s2, s3) the board configuration dip - switches offers the user to disable or disconnect spec ific devices or elements on the board. no bf name component signal description 1 pf1 ethernet n reset off : disconnect the ethernet reset signal nreset from pf1; controller remains in reset state on : connect the ethernet reset signal nreset to pf1 2 pf11 ethernet irq off : disconnect the ethernet interrupt signal irq from pf11 on : connect the ethernet interrupt signal irq to pf11 3 nams1 ethernet ncs off : disconnect the ethernet signal n cs from n ams1, controller remains unselected on : connect the ethernet signal ncs to nams1 4 nams2 usb n cs off : disconnect the usb signal n cs from n ams2; controller remains unselected on : connect the usb signal ncs to nams2 5 pf12 usb n irq off : disconnect the usb interrupt signal nirq from pf12 on : connect the usb interrupt signal nirq to pf12 6 pf13 usb n reset off : disconnect the usb reset signal nreset from pf13; controller remains in reset state on : connect the usb reset signal nreset to pf13
edev - bf5xx_hum_v2.0.docx 29 no bf name component signal description 7 pf2 t ouch screen controller npen irq off : disconnect the touch screen c ontroller interrupt signal npenirq from pf2 on : connect the touch screen controller interrupt signal npenirq to pf2 8 pf4/tmr4 display clk off : disconnect ppi1.clk from pf4 on : d rive the ppi1.clk with tmr4 output table 5 - 2 : dip s witch s etting description for s2 no bf name component signal description 1 pf10 p ush - button s4 off : disconnect push - button s4 from pf10 on : connect push - button s4 to pf10 2 rx uart rx off : remove pull - up resistor from uart - rx signal on : add 10k pull - up resistor to uart - rx signal 3 pf7 led v10 off : disconnect red led v10 from pf7 on : connect green led v10 to pf7 4 pf6 led v9 off : disconnect red led v9 from pf6 on : connect green led v9 to pf6 5 pf46 camera sio . d off : disconnect camera signal sio.d from pf46 on : connect camera signal sio.d to pf46 6 pf47 camera sio . c off : disconnect camera signal sio.c from pf47 on : connect camera signal sio.c to pf47 7 pf9 t ouch screen controller sda off : disconnect the sda signal of the touch screen controller from pf9 on : connect the sda signal from touch screen controller to pf9 8 pf8 t ouch screen controller scl off : disconnect the scl signal of the touch screen controller from pf8 on : connect the scl signal from touch screen controller to pf8 table 5 - 3 : dip s witch settings description for s3 5.6 boot mode switch (s6) to set the right boot mode, only the switches 1 and 2 are used. switches 3 and 4 are reserved for future use. switch setting boot description on off 1 2 3 4 execute from16bit ext ernal mem ory b ypass rom on off 1 2 3 4 reserved on off 1 2 3 4 boot from 8bit flash on off 1 2 3 4 boot from spi 16bit table 5 - 4 : boot m ode s ettings
edev - bf5xx_hum_v2.0.docx 30 5.7 uart routing switch (s5) switch position function 0 the uart is routed to the 4 - pin header 1 the uart is routed to the usb to uart b ridge table 5 - 5 : uart routing s witch s etting s
edev - bf5xx_hum_v2.0.docx 31 6 support 6.1 general support general support for products can be found at bluetechnix support site https://support.bluetechnix.at/wiki 6.2 b oard support packages board support packages and software downloads are for registered customers only https://suppor t.bluetechnix.at/software/ 6.3 blackfin ? software support 6.3.1 blacksheep? os blacksheep? os stands for a powerfully and multithreaded real - time operating system (rtos) originally designed for digital signal processing application development on analog devices blackfin? embedded processors. this high - performance os is based on the reliable and stable real - time vdk kernel from analog devices that comes with vdsp++ ide. of course blacksheep? os is fully supported by all bluetechnix core - modules and development hardware. 6.3.2 labview you can get labview embedded support for bluetechnix core modules by schmid - engineering ag http://www.schmid - engineering.ch . 6.3.3 uclinux you can get uclinux support ( boot loader and uclinux ) for bluetechnix c ore modules at http://blackfin.uclinux.org . 6.4 b lackfin ? design services based on more than seven years of experience with blackfin, blue technix offers development assistance as well as custom design services and software development. 6.4.1 upcoming products and software releases keep up to date with all product changes , releases and software updates of bluetechnix at http://www.bluetechnix.com .
edev - bf5xx_hum_v2.0.docx 32 7 ordering information 7.1 predefined mounting options for edev - bf5xx article number name description 100- 2 3 42 - 2 edev - bf5xx evaluation board without onboard debug - agent (sada) 100- 2343 - 2 edev - bf5xx - sada development board with debug - agent ( sada ) table 7 - 1 - ordering information note: custom hard and software developments are available on request ! please contact bluetechnix ( office@bluetechnix.com ) if you are interested in custom hard - and software developments .
edev - bf5xx_hum_v2.0.docx 33 8 dependability 8.1 mtbf please keep in mind that a part stress analysis would be the only way to obtain significant failure rate results, because mtbf numbers just represent a statistical approximation of how long a set of devices should last before failure. nevertheless, we can calculate an mtbf of the development board using the bill of material. we take all the components into account. the pcb and solder connections are excluded from this estimation. for test conditions we assume an ambient temperature of 30c of all developmen t board components. we use the mtbf calculator from ald ( http://www.aldservice.com/ ) and use the reliability prediction mil - 217f2 part stress standard. please get in touch with bluetechnix ( office@bluetechnix.com ) if you are interested in the mtbf result.
edev - bf5xx_hum_v2.0.docx 34 9 product history 9.1 version information version date changes 2.0 2011- 03- 31 new power supply for 5.0v and 3.3v additional buffers on data lines of ebi for better signal quality 1.0 2010- 12- 03 first release v1.0 of the hardware. table 9 - 1 : overview product changes 9.2 anomalies version date description 2.0 2011- 07- 18 no anomalies reported yet. 1.0 2010- 12- 12 poor signal quality on data lines of ebi table 9 - 2 : overview product anomalies
edev - bf5xx_hum_v2.0.docx 35 10 document revision history version date document revision 6 2012- 03- 26 updated dip switch setting description for s2 5 2011- 07- 18 updated boot mode table. 4 2011- 05- 19 dip switches description update 3 2011- 03- 31 update for hw - revision v2.0 2 2010- 12- 12 anomaly report for v1.0 added 1 2009 12 03 first release v1.0 of the document table 10- 1 : revision history
edev - bf5xx_hum_v2.0.docx 36 11 list of abbreviations abbreviation description adi analog devices inc. ai analog input ams asynchronous memory select ao analog output cm core module dc direct current dsp digital signal processor ecm enhanced core module ebi external bus interface esd electrostatic discharge gpio general purpose input output i input i2c inter - integrated circuit i/o input/output ism image sensor module ldo low drop - out regulator mtbf mean time between failure nc not connected nfc nand flash controller o output os operating system ppi parallel peripheral interface pwr power rtos real - time operating system sada stand alone debug agent sd secure digital soc system on chip spi serial peripheral interface spm speech processing module sport serial port tft thin - film transistor tism tiny image sensor module tsc touch screen controller uart universal asynchronous receiver transmitter usb universal serial bus usbotg usb on the go zif zero insertion force table 11- 1 : list of a bbreviations
edev - bf5xx_hum_v2.0.docx 37 a list of figures and tables figures figure 1 - 1: main components of edev - bf5xx .............................................................................................................................................. 9 figure 2 - 1: interconnection diagram ............................................................................................................................................................ 12 figure 2 - 2: interface overview ......................................................................................................................................................................... 14 figure 2 - 3: mechanical outline top view ...................................................................................................................................................... 15 figure 2 - 4: mechanical outline bottom view ............................................................................................................................................. 16 figure 2 - 5: recommended extender board layout ................................................................................................................................. 17 tables table 3 - 1: electrical characteristics ................................................................................................................................................................ 18 table 3 - 2: absolute maximum ratings .......................................................................................................................................................... 18 table 4 - 1 - connector description x1 ........................................................................................................................................................... 22 table 4 - 2 - conne ctor description x2 ........................................................................................................................................................... 25 table 4 - 3: blt - ism - connector interface description (x11) ................................................................................................................... 26 table 4 - 4: display interface description (x6) .............................................................................................................................................. 27 table 5 - 1: led connection description ......................................................................................................................................................... 28 table 5 - 2: dip switch setting description for s2 ....................................................................................................................................... 29 table 5 - 3: dip switch settings description for s3 ...................................................................................................................................... 29 table 5 - 4: boot mode settings ......................................................................................................................................................................... 29 table 5 - 5 : uart routing switch settings ..................................................................................................................................................... 30 table 7 - 1 - ordering information .................................................................................................................................................................... 32 table 9 - 1: overview product changes .......................................................................................................................................................... 34 table 9 - 2: overview pro duct anomalies ...................................................................................................................................................... 34 table 10 - 1: revision history .............................................................................................................................................................................. 35 table 11 - 1: list of abbreviations ..................................................................................................................................................................... 36

▲Up To Search▲

Price & Availability of EDEV-BF5XX

	To Download EDEV-BF5XX Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .